Yarn
Fingering weight yarn
(MC) Approximately 730 yards / 668 m
(CC) Approximately 730 yards / 668 m
Lichen and Lace 80/20 Sock (80% merino wool, 20% nylon; 365 yds / 334 m, 100g)
The sample is shown in Silver Fox 2 skeins (MC), Soot 2 skeins (CC)

Needles
A US 21⁄2 (3 mm) 16” / 40 cm circular needle Or needle required to obtain gauge

Gauge (after blocking)
26 stitches & 30 rows = 4” / 10 cm in color work pattern with US 21⁄2 (3 mm)

Size
Length: 94” / 239 cm
Width (measured flat): 7 1⁄2 / 18.5 cm

Tools
Stitch marker (1), tapestry needle

Skill Level
3/5

Note
This scarf is worked in the round. The solid color sections at the beginning and end of the scarf take approximately one skein of MC. Keep an eye on your yardage and make sure you don’t go beyond 50g on the first section. Work as many full repeats as you can so there will be enough to create a matching section at the end of the scarf. The two-color section takes approximately 100g of MC and 200g of CC. Work as many full repeats of Section 2 that CC will allow, before running out. During the rows which are worked with MC and CC there will be long float in which one of the colors will be carried behind. Make sure to leave the floats loose enough to avoid the surface of the fabric from puckering or tack the floats down on these particularly long sections. Since the scarf is a tube, there should be no worries of the floats catching on something once it is finished.
The charts in this pattern are slightly different from conventional color work charts and this is to create a jogless seam along the scarf. To achieve this jogless seam, half of pattern repeat is off set. Once the repeat is worked a few times it is very easy to fall into the rhythm of the pattern.

If you have any question, tips for knitting, etc., please post in amirisu group. amirisu will coordinate with the designer to answer your questions.
Thank you!

Yarn
Fingering weight yarn
(MC) 約730 yards, 668 m
(CC) 約730 yards, 668 m
Lichen and Lace 80/20 Sock (80% merino wool, 20% nylon; 365 yds / 334 m, 100g)
サンプル色はSilver Fox 2カセ (MC), Soot 2カセ (CC)

Needles
1 x US 21⁄2 (3 mm) 16” / 40 cmの輪針 または, ゲージが取れる太さの針

Gauge (ブロッキング後)
US 21⁄2 (3 mm)の針を用いて カラーワークパターンで26目 & 30段 = 10 cm

Size
長さ: 239 cm
幅 (平らに置いて): 18.5 cm

Tools
ステッチマーカー (1), とじ針

Skill Level
3/5

Note
輪で編むマフラー . 最初と最後の一色のセクション1でMCを合計約1カセ使うため, 最初のセクションでMCを50gを超えて使わないよう注意すること. 最初に50g以内で1模様の繰り返しを編めるだけ編むようにすれば, 最後でも同じだけ編めように十分に糸が残る. 二色のセクション2はMC約1カセ, CC約2カセ使う. ここではCCがなくなるまでチャートを繰り返せばよい. 裏側で糸を渡す時は編み地がつらないように緩めにしておく. 場所によって裏の渡り糸が長くなる時があるがマフラーがチューブ型で裏側は見えないので気にする必要はない.
チャートは模様のつながりがスムーズになるようにチャートの初めの模様半分を1段ずらしてあり, 普通のカラーワークのチャートと少し違うので注意すること. 少し編んでいくとパターンのリズムがつかめて編みやすくなる.

何かこちらのパターンで質問がある場合は、デザイナーへではなく、amirisuグループの質問ボードにポストして下さい。
よろしくお願いします。