This is recycled yarn, and in pictures you can see pilling from previous garment even if I haven’t washed mittens yet. ^^“
This is a very tight gauge for my yarn held double, but:
1) I want to use this yarn
2) I have to match gauge
3) I need a very warm pair of mittens an I want to avoid drafts of cold air passing through the stitches.
If this way mittens will be too stiff I’ll frog them, but at least I try.
Begun with provisional CO, knitted 10 rows.
Skipped useless setup row, stitch marker just gets in my way. Counting 17 sts and m1L (right mitten).
To determine the right length of both the palm and the thumb I need the “saddle point” at thumb’s joint to be done and finished, because it’s the crucial point for fitting. So after leaving thumb stitches on hold I worked a bit of the palm, left it on holder too, and worked the thumb first.
I made it 6 cm long before decreasing.
Palm is 10 cm long. No setup round.
Decreasing round 1: 13 sts, k2tog, k to end of needle (magic loop); on second needle k6, ssk.
Then I simply made decreases one on top of the other and at either end of the needle, reading knitting without even counting.
Unraveled provisional part, picked up stitches and worked the cuff from the top down. Knitted 12 rounds of k2 p2 rib (first round ending with k2 p1 M1).
Sewn BO.
My mittens are not too stiff except fot the tips, where overlapping stitches (decreases) make them a bit thicher. The left one is slightly bigger and softer, as usually I loosen tension as I work. Sigh.
I don’t really like the top shaping, but I can improve the final shape by blocking.
Il filato è riciclato, e nelle foto si vedono i pallini (fatti dall’indumento precedente) nonostante io non abbia ancora lavato i guanti ^^“
Il lavoro è decisamente stretto per il mio filato messo doppio, ma:
1) voglio usare questa lana
2) devo rispettare il campione
3) mi serve un paio di guanti molto caldi e senza spifferi tra un punto e l’altro.
Se poi saranno troppo rigidi e “gnucchi” li disferò, ma almeno ci provo.
Iniziato con avvio provvisorio, 10 ferri a diritto.
Saltanto l’inutile giro di impostazione, il marcapunti mi è solo d’impiccio. Conto 17 maglie e aumento (guanto destro).
Per determinare la lunghezza sia del palmo che del pollice devo avere il “punto di sella” all’attacco del pollice che sia fatto e finito, perché è il punto cruciale per la vestibilità. Quindi dopo aver lasciato in sospeso le maglie del pollice ho lavorato un pezzetto del palmo, ho lasciato in sospeso anche quello, e ho lavorato il pollice per primo.
L’ho fatto lungo 6 cm prima delle diminuzioni.
Il palmo misura 10cm. Saltato il giro di impostazione.
Giro di diminuzioni 1: 13 dir, 2insDir, dir fino alla fine del ferro (magic loop); sul secondo ferro 6 dir, ppd.
Poi ho semplicemente fatto le diminuzioni una sull’altra e alle estremità del ferro, guardando il lavoro senza nemmeno contare.
Disfatta la parte provvisoria, riprese le maglie e lavorato il polsino dall’alto in basso. 12 giri a coste doppie, finendo il primo giro con 2dir 1rov 1aum.
Chiusura con l’ago.
I guanti non mi sono usciti troppo rigidi, eccetto per le punte delle dita dove le maglie che si sovrappongono (diminuzioni) fanno un po’ di spessore. Il sinistro è un po’ più grande e morbido del destro, come al solito allento la tensione man mano che lavoro. Sigh.
Non mi piace molto la forma in cima, ma posso migliorarla alla fine col bloccaggio.